International Water Ski Federation 1999 Edition Homologation Dossier Note: Do not modify the following form except as noted by filling in the brackets as noted. After the end of the form as noted by the end label is the section where comments may be added. IMPORTANT NOTICE: It is not the intent of this form to add hours of extra work to the homologator's job, but rather to provide a quick checklist that gives visibility of the technical effort to the general skiing public. The files requested should already have been generated in the course of your set-up of the site. Just attach them as they were created with no special processing. The requirement for scoring and officiating files has been deleted. START OF HOMOLOGATION FORM Name of competition:3a PROVA COPPA ITALIA Date:09/09/2000 10/09/2000 Venue:FOSSO GHIAIA (RA) Organizing Country:ITALY Type of competition (use X) (X) International Calendar ( ) International Non-calendar ( ) National Were cash prizes or merchandise awarded (Yes/No) (Yes ) Homologator's and Chief Judge recommendation to Tournament Council (Fill in R-Record, L-Standing List, N-Not list capable) Event Round 1 Round 2 Round 3 Round 4 Slalom (R) (R) ( ) ( ) Tricks (R) (R) ( ) ( ) Jump (R) (R) ( ) ( ) OBLIGATORY COMPOSITION OF DOSSIER: 1 copy of this document including the homologation notice OPTIONAL ADDITIONAL FILES 1 slalom survey (if applicable) example - sl98FRA13.xls 1 jump survey (if applicable) example - ju98FRA13.xls video jump files example vja98FRA13.wks, vjb98FRA13.wks HOMOLOGATOR'S CHECKLIST If checked and all according to rules put OK in brackets. If checked and any variation to the rules put an X in the brackets and explain in "Remarks" section on last page. Not applicable is NA. 1. Boats and equipment (W 10.01) (OK) 2. Speed Control (W 10.07) ( ) Manufacturer:PERFECT PASS Software Version:4.01B slalom (OK) tricks (OK) jump (OK) 3. Arrangement for checking skis (W 10.03) (OK) 4. Measure lines and handles (W 10.04) ( ) slalom (OK) jump (OK) handles (OK) 5. Arrangement for checking of skier supplied handles (W 10.06) (OK) 6. Timing devices (W 11.03) (OK) 7. Homologation notice posted before start (OK) 8. Automatic timing-jump (OK) 9. Jump distance indication (W 13.11) (OK) 10.Video Jump Distance measurement (W 13.11)(OK) Backup - video tape (OK) or standard meters ( ) 11.Automatic timing-slalom (OK) standard segment ( ) all buoy (OK) 12.Position and height of slalom towers (OK) (W 14.05 and W diagram 6) 13.Slalom buoys (W 14.06) (OK) 14.VHS video slalom endcourse (W 14.17) (OK) 15.Trick course checked (W diagram 3) (OK) 16.Position and height of trick towers (OK) (W 15.11) 17.Semi-automatic timing-20sec (W 15.12) (OK) with automatic median start ( ) 18.VHS video tricks (W15.15) (OK) 19.10,000 points review judge (W 15.15) (OK) SLALOM COURSE (indicate which type with Yes) Four lines floating course (Yes) Single anchor buoys ( ) Center Line Frame per rules ( ) Attach survey document in plain monospaced text or a standard spreadsheet file type (.wks,.xls). If you have the latest version it is best to save it in an older version to assure compatibility. Attach it at the end after the Homologation Notice JUMP COURSE Attach survey document in plain monospaced text or a standard spreadsheet file type (.wks,.xls). If you have the latest version it is best to save it in an older version to assure compatibility. Attach it at the end after the Homologation Notice JUMP MEASUREMENT SETUP VIDEO JUMP Attach survey of buoys (if used) at the end after the Homologation Notice Attach spreadsheet printout for each camera position at the end after the Homologation Notice JUMP RAMP Width at top (W 13.02a) 4.26 m Width at bottom 4.26 m Top edge to 6.4m line left side (W 13.02b,h) 6.40 m Top edge to 6.4m line right side (W 13.02b.h) 6.40 m Top edge to 6.7m line left side (W 13.02b,h) 6.70 m Top edge to 6.7m line right side (W 13.02b.h) 6.70 m Length underwater from 6.7m line (W 13.02c) 1.30 m Maximum Deviation from plane Diagonal string measurement (W 13.02f) 0 cm Center string measurement (W 13.02f) 0 cm (OK/X) Apron under water (W 13.02g) (OK) Apron full length (W 13.02g) (OK) Sighting line (W 13.02i) (OK) Secure anchoring (W 13.02i) (OK) Apron Angle (W 13.02k) jump height 1,60 m (a) length of edge of apron from top corner to water 2,10 m (b) ratio of b/a 0,762 ( ) minimum 0.883 maximum 0.643 RAMP SETTING Right Side Left Side Setting Height Length Ratio Height Length Ratio 1.50 1,60 6.80 0,235 1,60 6,80 0,235 1.65 1.73 6.80 0,254 1,73 6,80 0,254 1.80 1,83 6,80 0,269 1,83 6,80 0,269 Note: If video jump is used, disregard the following section noted by an * on each line *NON-VIDEO JUMP *Note: If this information is generated by a program, *the result file may be attached here rather than re-copying *the information on to this form. Be sure that it *contains all of the requested information which it *should for a proper set up program. *Automatic meter system used (Yes/No) ( ) *Protractor reading units (Degrees/Grades) ( ) *METER SETUP *Distance (T1 - T2/A - B) (XXX.XX meters) *Distance (T2 - T3/B - C) (XXX.XX meters) *if not a straight line *Distance (T1 - T3/A - C) (XXX.XX meters) *Inter-meter angles (if not a straight line) T1/A T2/B T3/C *Meter T1/A XXXXX 180.0 180.0 *Meter T2/B 0.0 XXXXX 180.0 *Meter T3/C 0.0 0.0 XXXXX *(note shown numbers are examples - fill in with actual *numbers) *SET UP SIGHTINGS *Angle Ramp 15ET *T1/A upper XXX.X XXX.X *T1/A lower XXX.X XXX.X *T2/B upper XXX.X XXX.X *T2/B lower XXX.X XXX.X *T3/C upper XXX.X XXX.X *T3/C lower XXX.X XXX.X *Using average of upper and lower readings (max difference * 0.1 degrees) list the error triangles with an inscribed * circle diameter (max 0.15) *inscribed circle diameter at ramp X.XX meters *inscribed circle diameter at 15ET X.XX meters *Jump system survey results (X-Y coordinates) *Ramp X Y *Table 1/A XXX.XX XXX.XX *Table 2/B XXX.XX XXX.XX *Table 3/C XXX.XX XXX.XX *Buoy 15ET XXX.XX XXX.XX *Attach the computer printout file *at the end after the Homologation Notice *Computer program checked against (OK/X) *"Computer Benchmark for Computed Distances" ( ) *METER STATIONS *Stability and horizontal level ( ) *Protractors on same vertical line ( ) *Protractor graduations (max 0.2 degrees) ( ) *Diameter of protractors (min 0.25 m) ( ) *Accuracy of sighting arms ( ) END OF HOMOLOGATION FORM It is important to leave the above section in the exact format as it will be processed automatically. The following section is where free form comments are added and attachments are made. HOMOLOGATOR'S REMARKS Give details of any variations of IWSF rules. List any alterations to the course, etc. duringthe competition. List any malfunction of equipment. Give any further information which might affect the Tournament Council's assement of the homologation. Homologator: CANDIDO MOZ VIA S. MARIA 4 31020 REVINE LAGO (TV) ITALY Chief Judge: PAOLO BARBIERI ARNALDI VIA CAVALLEGGERI, 34 26900 LODI ITALY Please email this homologation record to bcorson@telesciences.com within 7 days of the end of the tournament.